Browse
Categories

Creating a Parapet Roof

Reference Number: KB-00120 Last Updated: 05-29-2014 10:25 AM

The information in this article applies to:


QUESTION


How do I create a flat roof with ­parapet walls?


ANSWER


Follow the instructions below to create a flat roof structure with parapet walls.  First we will begin by starting a New Plan  and creating the basic structure described below.

 

To draw the initial plan

  1. Select Build> Wall> Straight Exterior Wall  and draw four walls in a clockwise manner to make a simple rectangular house.


  2. Select Build> Floor> Build New Floor  from the menu to open the New Floor dialog.


  3. In the New Floor dialog, choose Make new (blank) plan for the 2nd Floor to create a new floor based on the footprint of the 1st floor plan and click OK.

     


  4. After clicking the OK button, the Floor 2 Defaults dialog will display, which allows you to enter in a value for the Finished Ceiling (F).



    For the purposes of this example, we will set this value to 36".

Once the first floor is created, we are ready to begin on creating the parapet for our second floor.

 

To create parapet walls over the first floor

  1. With Floor 2 active  , select Tools> Reference Floors> Reference Floor Display , or press the F9 hotkey keyboard shortcut, to see how the second floor relates to the first.


  2. Select Build> Wall> Straight Half-Wall *  child button and draw four half walls in a clockwise manner directly on  top the reference for the first floor walls to make a simple enclosed  rectangular structure.

    Note: In some versions of the software, the  Straight Half-Wall tool may not   be available.  In these programs, you  should instead use a Straight Railing defined as Solid on the Railing tab of its specification dialog.


  3. The Half Walls should snap directly to the reference display lines of   the first floor walls, however, if you create a half wall and it is not   aligned, select the Align with Wall Below  edit tool.

You can also select the railing, Zoom In, hold down the Ctrl key on your keyboard to allow for unrestricted movement, and use the    half-wall or solid railing's Move edit handle to precisely position it.


After your Half-Walls, or Solid Railings, have been created, you can adjust how they display.

 

To Adjust the Display of Your Parapet Walls

  1. Using the Select Objects  tool, select one of the Half Walls, and click on the Open Object  edit button to display its Specification dialog.


  2. On the General panel, set the Thickness.

    For the purposes of this example, we will set the value to be 10 7/16" so that it matches the Brick-6 Wall Type used on Floor 1.


  3. On the Newels/Balusters panel, specify the Railing Height.



    For the purposes of this example, we will set this value to be 24"

    Make sure that you do not set the Railing Height value higher than the Finished Ceiling Height you specified earlier, or the Railings will  not display correctly.



  4. Once you have completed these changes, click OK to apply them and close the Railing Specification dialog, and repeat the process for the remaining three Half Walls on Floor 2.

Now that we have completed drawing in the parapet walls on Floor 2, we are ready to modify the room that makes up the inside of the parapet.

 

Defining the Second Floor Parapet Room

  1. Using the Select Objects tool, click in the middle of the second floor room, and then select the Open Object  edit button to display the Room Specification dialog.


  2. In the Room Specification dialog, on the Structure panel, notice that the Finished Ceiling (F) is set to 36" and then uncheck Ceiling Over This Room and Roof Over This Room.




  3. On the Moldings panel, uncheck Default and click on the Delete button to remove the Default Base Molding.




  4. Go to the Materials panel and select Floor Finish, then click the Select Material button to display the Select Materials dialog.




  5. Browse to an appropriate material, then click OK to apply the changes so it is visible in the Room Specification dialog for the Floor Finish.

    For the purposes of this example, we used the Asphalt-02 material


  6. Next, select 3D> Create Camera View> Perspective Full Overview  to see your flat roof parapet wall structure thus far.

     

While still in your 3D camera view, you can change the materials  associated with your railings to match the rest of the house.

 

To Change the Materials of the Parapet Walls in a Camera View

  1. Select 3D> Material Painter> Material Eyedropper .


  2. Click on the exterior wall material for the wall below the railing  to select that same material, activating the Material Painter in  Component Mode, which changes your mouse cursor to look like this .


  3. With the Material Painter spray can tool active, click on the exterior of each railing to change it to the same material as the wall below.


  4. One all of the railings are matching exterior materials with the wall below, you can select 3D>Material Painter> Material Painter to display the Select Library Object dialog, browse to an appropriate material, and apply it to the handrails for the tops of the Half Walls as well.



    You are now ready to further customize the plan, or take the knowledge you have gained and apply it to your own parapet design.